Quick Answer: Can I Add Shock And Stabilizer At The Same Time?

What happens if stabilizer is too low in pool?

If the Stabilizer level tests lower than 30 ppm it will be difficult to maintain a chlorine level, because any chlorine added to your swimming pool will quickly evaporate and burn off in direct sunlight.

If the Stabilizer level tests above 50 ppm it will also be difficult to maintain a chlorine level..

How long after adding algaecide can you shock?

Keep your pump and filter running. Give the shock a good 12 to 24 hours to work it’s magic. If the algae hasn’t cleared up after 24-48 hours, clean and brush the pool and add another shock treatment.

Does shocking pool raise pH?

Chlorine based pool shock (Calcium Hypochlorite) has a high pH, and will naturally raise the pH level of your swimming pool water, in addition to changing your chlorine level. Chlorine free shock has a neutral pH, and will not affect any of your pool chemical levels.

Do I add chlorine or stabilizer first?

Open your pool under normal procedures, and let the filter run with its normal amount of chemicals. When all the other chemicals, such as chlorine. pH and alkalinity, are balanced, add the chlorine stabilizer. Add the stabilizer only after the filter has been backwashed to ensure it is cycled through a clean filter.

Is shock and stabilizer the same thing?

Also known as pool conditioner, chlorine pool stabilizer, or chlorine stabilizer you can buy this chemical additive as either liquid or granules. It’s also often called cyanuric acid, a chemical that may be included in chlorine tablets or sticks (called trichlor) or shock (called dichlor).

Is pool shock a stabilizer?

Pool stabilizers are sold in liquid and granule form. They are also even sold mixed in with chlorine tablets, sticks, and chlorine shock. These combination products are known as Stabilized Chlorine because the stabilizer is mixed in with the sanitizer.

Can you put too much shock in a pool?

You can, however, use more shock than you need – or less than is sufficient. In other words, while you shouldn’t worry too much about adding a little extra pool shock, there is still a right way and a wrong way to shock your pool if you want to get the best results.

Do I use shock or algaecide first?

Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.

Can you shock your pool and add stabilizer at the same time?

You can even get it mixed in with chlorine tablets or sticks, called trichlor, and in chlorine shock, called dichlor. These combination products are referred to as stabilized chlorine because the stabilizer is mixed right in with the sanitizer, saving you the trouble of measuring and adding them separately.

Will low stabilizer cause cloudy pool?

Low chlorine levels or inconsistent peaks and valleys, can cause hazy pool water. Also, check that you have a residual of stabilizer, aka conditioner – to help protect the chlorine from the sun. … Usually DE will settle out fairly quickly, but if there is a lot of blow-back, it will cloud the pool continuously.

What happens if stabilizer is too high in pool?

What Happens When You Have Too Much Stabilizer? If the stabilizer level is too high in a pool it, will lock the chlorine molecules, rendering them ineffective as a sanitizer. … Although you will get a chlorine reading—sometimes a high chlorine reading—your pool may still have algae or other problems.

Is baking soda a pool stabilizer?

Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.

How often should a pool be shocked?

It’s often recommended to shock your pool once a week. If you don’t do it every week, you should at least do it every other week. This is necessary to maintain your pool’s water chemistry. If you have a lot of people over in your pool or have a party, you may want to shock your pool more frequently.

Can you add salt and shock at the same time?

Should you add shock to a salt water pool? It’s absolutely okay to shock your salt water pool, and is actually pretty important! Running your pool’s super-chlorinate feature too often is hard on the motor and will cause it to wear out faster.

Can you add pH up and shock at the same time?

Using liquid chlorine raises the pH of the water. Liquid chlorine does not raise pH. … Chlorine shock + Sequester Agent: Chlorine shock will also disrupt stain & scale chemicals, aka chelators or sequestering agents, if added at the same time.

Can you put stabilizer directly in pool?

How to add stabilizer to your pool. Most manufacturers say to add your CYA to a bucket of warm water first and others say you can pour it directly into the pool.

How long after adding stabilizer can I swim?

It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.